• Player who is looking for higher trajectory with low kickpoint shaft.
  • Player who would like to reduce slices for longer distance.
  • Player wanting straighter shots.
  • Lady golfer who has higher-than-average swing speed.
  • Player who is looking for forgiveness.

HONMA's special FW with long carry performance and control.

  • 3W adopts the cup face with high deflection on impact for a long carry distance.

    The amount of deflection depends on the golfer but will achieve control, powerful trajectory and longer carry distance.

  • The enhanced potential of the new head design

    The lower center of gravity expands the length of the face and allows us to bring the center of gravity on the face closer to the center point, resulting in a higher smash factor.

  • All clubs become ordnances with the center of gravity flow design

    The fairway wood series performance is enhanced by controlling the sole thickness for each club.

Cup face structure

The thin section of the upper and lower face increases the amount of face deflection, which increases the repulsion, providing control and powerful trajectories (adopted for #3 only).

Crown's partially different thickness design

The reinforced internal mesh structure is optimized on the S-05 FW crown. This design optimizes the deflection and resilience during impact.

Inclination of head at address lie (45°).

With the previous model, there is dead space between the toe side of the sole and the ground at address. S-05 FW has the sole shape in which the sole surface on the toe side is brought close to the ground, which reduces the dead space, lowering the center of gravity by 2.5mm, even though the face height is 2mm higher (compared to S-03 #3). As a result, height of the hitting area is expanded 4.5mm, and gains high trajectory with low spin. This provides an easier address position.

The thickness is controlled for each club by the center of gravity flow design

The deep/low center of gravity grips the ball at impact. Balls are easier to hit in high and straight, providing longer carry distance.

With the shallow center of gravity, balls are prevented from being over-gripped, allowing you to stop the balls in fade trajectories with the appropriate spin.


Head material/Manufacturing process SUS630/Forged
Face material/ Manufacturing process High-Strength Custom Steel/Forged
Shaft ARMRQ∞ 48, ARMRQ∞ 53, ARMRQ∞ 44
# (No.) 3W 5W 7W
Length(inches) 43.0 42.5 42.0
Loft (deg.) 15 18 21
Head volume (cm 3) 190 179 171
Lie angle (deg.) 59.0 59.5 60.0
Distance to Center of Gravity(mm) 33.0 32.5 32.0
Height to Center of Gravity(mm) 23.0 24.0 24.0
Effective hitting area(mm) 15.0 13.5 13.0
Depth to Center of Gravity(mm) 32.0 31.5 31.0
Gravity Angle(deg.) 27.0 24.0 22.0
weight (g)
ARMRQ∞ 48 R D0・298 D0・302 D0・306
SR D1・301 D1・305 D1・309
S D1・302 D1・306 D1・310
ARMRQ∞ 53 R D0・309 D0・313 D0・317
S D1・313 D1・317 D1・321
ARMRQ∞ 44 R D0・295 D0・299 D0・303
Data refers to the 2S grade
Made in Japan
2S 3S 4S


Material Carbon+eight-axisUD
Kick-point Low-Mid
Flex R,SR,S
Butt diameter (mm) R 15.3
SR 15.3
S 15.4
Tip diameter (mm) 8.6
# (No.) 3W 5W 7W
Gross weight (g) R 48.0 47.5 47.0
SR 49.5 49.0 48.5
S 51.0 50.5 50.0
Torque (deg.) R 4.45
SR 4.40
S 4.35
Frequency (cpm) R 254 261 268
SR 262 269 276
S 270 277 284

Data refers to the 2S grade/1W shaft only


Material Carbon+eight-axisUD
Kick-point Mid
Flex R,S
Butt diameter (mm) R 15.4
S 15.5
Tip diameter (mm) 8.6
# (No.) 3W 5W 7W
Gross weight (g) R 53.5 53.0 52.5
S 56.5 56.0 55.5
Torque (deg.) R 3.75
S 3.65
Frequency (cpm) R 273 280 287
S 289 296 303

Data refers to the 2S grade/1W shaft only


Material Carbon+eight-axisUD
Kick-point Low
Flex R
Butt diameter (mm) 15.1
Tip diameter (mm) 8.6
# (No.) 3W 5W 7W
Gross weight (g) 43.5 43.0 42.5
Torque (deg.) 5.40
Frequency (cpm) 220 225 230

Data refers to the 2S grade/1W shaft only



Name BERES RubberⅢ
Material Rubber
Shaft ARMRQ∞ 48, ARMRQ∞ 44 ARMRQ∞ 53
Gross weight (g) 38 43
Size 60 60

Data refers to the 2S grade/1W shaft only